HMEMC

EMI Power Line Filters for Shielded Rooms and Anechoic Chambers

A shielded room is only as good as its worst penetration. Every cable that enters the room carries interference in and out. HMEMC builds the filters that close that hole: single and three phase mains filters from 3 A to 2200 A, 400 Hz and DC variants, and signal, telephone, USB, LAN and fire alarm filters for everything else that has to get inside.

3 A to 2 x 2200 A220 / 380 / 400 / 440 V400 Hz and DCInsertion loss to 100 dB

Why the filter, not the panel, decides performance

Panels are the easy part of a shielded room. A well-built enclosure with a badly chosen filter leaks along the power cable, and the measurement fails at the frequencies nobody tested during installation. In practice most shielding performance complaints trace back to a penetration, not to the panel seams.

Two things make a mains filter work in this application: enough insertion loss across the band you actually care about, and correct installation — short, shielded cable runs on the clean side, and the filter housing bonded to the room's shielding. A filter bought on current rating alone is a filter bought twice.

Power line filters

Standard ranges, all with manganese-zinc ferrite cores and multi-stage LC construction:

CurrentConfigurations
3 A – 6 A2-wire and 4-wire, C grade, 220 V / 380 V
10 A – 20 A2 x 10 A, 4 x 10 A, 2 x 16 A, DC variants, 400 Hz variants
30 A2 x 30 A and 4 x 30 A, single and three phase, military EMP variants
50 A – 80 A2 x 50 A, 4 x 50 A, 2 x 60 A, 4 x 80 A at 115 V, 250 V and 400 Hz
100 A – 150 A1 x 100 A, 2 x 100 A, 4 x 100 A, DC up to 1000 V, 400 Hz, 440 V
200 A – 300 A1 x 200 A, 2 x 200 A, 4 x 200 A, 4 x 250 A, 4 x 300 A at 400 Hz
400 A – 2200 A4 x 400 A, 4 x 500 A, 4 x 600 A, 2 x 800 A, 2 x 2200 A

Typical insertion loss on standard designs is 100 dB from around 100 kHz to 40 GHz in the common mode, with the differential mode curve specified separately per model — a filter cannot be judged by one number, and any supplier quoting a single figure is hiding the shape of the curve.

Voltage and frequency variants

Signal and control filters

The mains feed is only one penetration. A typical chamber has a dozen more:

Every one of these exists because somebody tried to run the cable straight through and watched the shielding effectiveness collapse. If your room needs a signal type that is not on this list, that is a design conversation, not a catalogue problem.

Installation notes that matter

Frequently asked

How do I choose the current rating?

On the actual load current plus margin, but the rating is only the starting point. What matters is the insertion loss curve over the frequency range your test standard covers, and the mounting arrangement.

Do you supply filters separately from rooms?

Yes. Filters are supplied as standalone components, including to customers who are building or upgrading rooms themselves.

Can you build a filter for a non-standard voltage or frequency?

We build 400 Hz, DC, 440 V and EMP variants as standard ranges. Anything further out is a custom design — send the specification.

What about signal lines?

Telephone, USB, LAN, RS485, video, DVI, audio, fire alarm and fibre optic feedthroughs are all available. Fibre is usually the better answer for any signal that can be converted.

Where filters do not fix the problem. A filter stops conducted noise on the line it is installed in. It does nothing about a cable that leaves the room unfiltered, an earth conductor carrying the noise out, or radiation from a badly sealed door. We have seen rooms where the customer bought the highest specification filters available and still failed, because the leak was the door seal. If the failure is radiated, start with the shielding survey, not with the filter. On sizing: a filter rated above the actual load runs cool and filters well; a filter pushed to its rating runs hot and its insertion loss drops. Give us the real load, not the breaker size.

Ask about EMI power filters

Five fields, no registration. We reply to every enquiry within one working day.

Or email sales.cn@hmemc.com

Prefer to write or call directly?

sales.cn@hmemc.com  |  kubohua@hmemc.com  |  +86 519 8665 1804

Changzhou, Jiangsu, China · Mon–Sat, GMT+8