HMEMC
中文站  |  sales.cn@hmemc.com  |  kubohua@hmemc.com  |  +86 519 8665 1804
English › Shielded Rooms

RF Shielded Rooms: Modular and Welded, 14 kHz to 18 GHz

A shielded room either attenuates or it does not, and the answer is decided at the penetrations. Panels are a solved problem. Doors, filters, vents, cable trays and the way the floor meets the wall are where rooms quietly lose 20 to 40 dB.

Two ways to build it

Modular, bolted panelsWelded
Panel3 m × 1 m double-sided hot dip galvanised steel, ≥ 2 mm, zinc ≥ 20 µm (≥ 275 g/m²), folded twice on all four edgesSteel sheet, continuously seam-welded
JointM10 flange bolts at 100 mm pitch through conductive mesh gasketContinuous weld, no gasket to age
AssemblyOn site, inside an existing building, no hot workWelding on site, and that is the critical path
Typical performance80–100 dB depending on frequencyHigher, especially at 14 kHz
Can be movedyes, panels re-usedno
Best forupper floors, rented buildings, rooms that get reconfigured, sites with no hot work permitmetrology rooms, MRI rooms, military labs, low frequency work
Lead timeshorter, panels pre-fabricated in the factorylonger, site welding dominates

Shielding effectiveness targets

Modular rooms are tested to EN 50147-1, GB/T 12190-2006, GJB 5792 and IEEE Std 299 methodology. Field, frequency, typical attenuation:

FieldFrequencyTypical SE, modular room
Magnetic14 kHz60–75 dB
Magnetic100 kHz90–100 dB
Electric1 MHz – 1 GHz100 dB
Plane wave / microwave1 GHz – 18 GHz100 dB

14 kHz is the hard one, and it is magnetic rather than electric. Thin galvanised steel is transparent to low frequency magnetic fields unless the panels are thick, the seams are continuous and every hole is closed. If your requirement is 14 kHz at 90 dB, welded construction with a high-permeability inner layer is a different product, not an option on the modular one.

A real specification, line by line

This is the reference design we issued in March 2022 for a shielded computer room, model HM-SR-16. It is a good example of how the numbers look before anyone starts talking about performance.

ItemModelSpecification
Shield bodyHM-SR-16Double-sided powder coated, 2 mm single layer galvanised steel, bolted modular structure, self-supporting steel frame with independent top support. Overall 11.5 m L × 2.70 m W × 2.80 m H.
DoorHM-SD-MManual swing shielded door, painted finish, clear opening 1.00 m × 2.00 m
Raised floor—Anti-static raised floor, 500 kg/m² load
Power filtersHM-PF-4×32A / HM-PF-2×32Athree phase 32 A 380 V 50/60 Hz ×1; single phase 32 A 220 V 50/60 Hz ×1
Network—fibre optic conversion for the RJ45 port, 1000 Mbit/s
Vent windows—300 × 300 mm, cut-off frequency 18 GHz, 8 units
Lighting—8 × LED interference-free luminaires, clean PVC panel ceiling
Distribution—matching distribution board, breakers and light switches by the customer

The shielding figure for that room

FieldFrequencyCommitted SE
Magnetic14 kHz≥ 60 dB
Magnetic100 kHz≥ 70 dB
Magnetic100 kHz – 100 MHz≥ 100 dB
Plane wave200 MHz≥ 100 dB
Plane wave500 MHz≥ 90 dB
Plane wave1 GHz≥ 90 dB
Microwave18 GHz≥ 80 dB

Note what happens here. The room reaches 100 dB in the middle of the band and is committed to 80 dB at 18 GHz. That is not a weak room, it is a room with a normal door and eight vent windows in it, and the figures are honest about where the performance falls off. A vendor quoting a flat "100 dB, 14 kHz to 18 GHz" for a room with this many penetrations is quoting the panel, not the room.

What goes through the wall

Every one of these is a hole in the shield. The room's real performance is the shell figure minus the worst penetration.

PenetrationRange we buildWhat matters
Shielded doorsmanual, electric, pneumatic, sliding; 1.0, 1.2 and 1.5 m clear width; double-knife seals with beryllium copper finger stripThe door is the single biggest contributor to loss. Doors are assembled with their frame in the factory and shipped as one unit, so the frame cannot distort in transit — that is what destroys performance.
Power filters3 A to 2200 A; single and three phase; 220, 380, 400, 440 V; 400 Hz and DC variantsOne filter per circuit, sized to the load. Adding a circuit later means cutting a hole, so plan spare capacity now.
Signal filterstelephone, LAN, USB, RS485, fire alarm, video, audio, fibre opticFibre is the cleanest option where the signal will allow it: no conductor, no waveguide cut-off to worry about.
Honeycomb vents2.5 to 8 mm cell, 5 to 120 mm thick, brazed, 10 kHz to 18 GHzCut-off frequency is set by cell size and depth. 300 × 300 mm at 18 GHz has become our standard vent.
Waveguide penetrationsfibre optic, infrared emitters, gas and water linesRound waveguide, typically 50 mm
Shielded glass80 to 300 mesh, to GJB 151BMesh density sets the upper frequency limit
Filter wall / pass-through panel300 × 600 mm plates with N, BNC, SMA, FSMA, six-hole fibre waveguide, fibre interfacesRemovable with sealing compound, so a future upgrade does not mean cutting the shield.
Ground interface panel300 × 300 mm plates near the test tableN, SMA and FSMA connectors, quantity agreed per project

How the vents are actually arranged

Vent windows are pre-mounted in the factory, with no bolt passing through the shield, because a bolt through the shield is a permanent leak and a permanent argument with the test house. Air comes in through wall mounted vents and leaves through the ceiling, above the light fittings. At about 4 m/s air speed that gives three to four air changes per hour. The vent units come apart for cleaning, and the external flange is insulated from the HVAC duct.

Grounding

Every power filter and the shield body itself go to a single point earth through a copper bar welded and bolted to the shield. Insulating pads under the panels hold the whole room above earth, so the resistance at the single point stays below 1.0 Ω. The copper tape from the building earth to that point should be at least 50 mm × 5 mm. The earth point itself is supplied by the customer, and the resistance has to be right before we connect.

The test that separates suppliers

Ask for shielding effectiveness measured on the finished room with the door closed, the filters fitted and the vents installed. Not the panel test, not a sample of panel, the room. A supplier who reports 100 dB at 1 GHz for a room with a 1.2 m door and six filter penetrations should be asked where exactly that measurement was taken.

In our experience the real number for a well-built modular room in the 1–18 GHz band is 80–100 dB, and the door seal decides which end of that range you get.

Reference projects

Germany, 2022

Three modular shielded chambers plus four RF doors, filters, vents and accessories for an automotive electronics test facility. Sizes 7 500 × 5 500 × 2 550 mm (two rooms) and 6 500 × 5 000 × 2 550 mm. Panels shipped: 51, 51 and 92. Two containers, heaviest pallet 2 100 kg.

Northwest Institute of Nuclear Technology, China

Eight double-layer, fully welded, moisture-proof shielded enclosures, model HM-SC-2507A, tested to GJB 5792A-2021 over 14 kHz to 10 GHz by the Jiangsu Institute of Metrology, reports E2025-40841 through E2025-40848.

China Academy of Engineering Physics, Mianyang

Production batch of shielded cabinets and small shielded rooms.

Frequently asked

Modular or welded, which should I choose?

If the building will not take hot work, if the room must later be moved or extended, or if you rent the floor, modular. If it is a metrology room, an MRI room, or a military laboratory where 14 kHz matters, welded. The price difference is smaller than the performance difference at the low end.

Can a modular room reach 100 dB at 1 GHz?

Yes, with good doors and correctly treated penetrations. Where it fails is usually the door seal and the cable tray, not the panels.

How much floor loading do the panels impose?

About 20–25 kg/m² of wall area for double-sided 2 mm galvanised panel with accessories. A 7.5 × 5.5 m room with 2.55 m walls is roughly two tonnes of steel. The structural check usually comes out fine, but it has to be done.

Do you provide the room in a building that is still under construction?

Yes, and that is the best time. Coordinating the floor slab, the door opening and the penetrations before the concrete is poured saves more money than any discount on the room itself.

What has to be ready before you arrive on site?

Floor loading around 2 000 kg/m², flatness within ±3 mm over any 3 m, damp-proofing and an insulating layer, insulation resistance above 2 MΩ, and a single point earth measured below 1.0 Ω. Ambient 10–40 °C and 10–95 % RH in both the control room and the test room. Seismic design to intensity 7.

What we will not pretend. A modular room is not a 14 kHz solution past about 75 dB, and we will say so rather than sell you the modular version and hope. Same on very large rooms: beyond roughly 15 m span the steel structure becomes a structural engineering project of its own, and if that is the brief we will tell you at the quotation stage.

Where we have shipped

Market notes and project references, by country:

GermanyPolandUnited StatesCanadaUAE & GulfIndiaVietnamIndonesiaTurkeySouth Africa

Ask about shielded rooms

Five fields, no registration. We reply to every enquiry within one working day.

Or email sales.cn@hmemc.com